Plumbing Basics: What You Need for Bathtub Installation
Plumbing Basics: What You Need for Bathtub Installation
Blog Article
The publisher is making a few good pointers on A Step-by-Step Guide to Installing a Bathtub in general in this post down the page.
Installing a bathtub isn't exactly rocket science, but it does need solid plumbing, woodworking, as well as sometimes, tiling skills. Changing an old tub with a new one is additionally a moderately hard task. If the old bathtub is easily available, the job can move quickly; if you need to open up a wall surface to get rid of the old tub and place the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's skills, although you will certainly need a helper to leave the old tub and set in the brand-new one. Ensure you have qualified yourself for the work and also are comfortable trying it. Instead of hiring a contractor to take over a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you might require a specialist plumber to make tube links.
This post will assist you mount a brand-new bath tub in your bathroom if you have already purchased a new bathtub and also do not require to transform the plan of your previous supply of water pipelines.
Your devices and material checklist need to make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you ought to do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of removing the existing faucets can be fairly bothersome due to the limited accessibility that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a towel all set for the remaining water that will certainly come from the pipelines. Once the supply pipes have been eliminated, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the solitary taps from transforming throughout this process. When the taps have been eliminated, the holes in the bath/basin will have to be cleansed of any old securing compound.
Prior to going on to fit the brand-new faucets, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines are in place in between the faucet as well as the sink. Protect the faucet in position with the producer offered backnut. As soon as the tap is firmly in position, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The previous kind needs to be attached to the tap finishes first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Bathtub
Utilizing the two wood boards under its feet, place the bathtub in the required placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The following goal is to make sure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also readjusting the feet on the bathtub till the spirit level checks out degree.
To mount taps, fit the bottom of the furthest adaptable faucet adapter to the ideal supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the water supply and inspect all joints and new pipework for leakages as well as tighten them if needed. Fill up the tub as well as additionally examine the overflow electrical outlet and also the regular outlet for leakages.
Lastly, fix the bathroom paneling as explained in the manufacturer's instruction manual. Tiling and also sealing around the tub should wait up until the tub has actually been used at the very least when as this will resolve it right into its final placement.
Preparing for the Setup
To start with, the supporting frame supplied with the bath should be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the faucet comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is additionally practical to fit a supporting plate under the taps system to prevent stress on the tub.
Fit the adaptable faucet connectors to the bottom of both faucets making use of 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. See to it you make use of every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Tiling Around the Tub
In the location where the bath fulfills the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break a rigid seal, triggering the water to pass through the wall in between the bath and the tiling, resulting in complications with wetness and feasible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes and cartridges, and are capable of securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bathtub with water before securing, to enable the motion experienced when the bathtub is in use. The sealant can split rather very early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently readily available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader about How to Install a Bathtub, I thought sharing that blog post was important. Enjoyed reading our piece? Please share it. Let somebody else locate it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Explore Report this page