Essential Plumbing Insights for Bathtub Installation
Essential Plumbing Insights for Bathtub Installation
Blog Article
What are your ideas about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bath tub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old tub with a brand-new one is also a reasonably hard task. If the old bathtub is readily accessible, the task can move quickly; if you need to open a wall to remove the old tub and also position the new bath tub, the task is much harder. In either instance, the task is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also set in the brand-new one. Make certain you have actually certified on your own for the task and are comfortable trying it. As opposed to employing a professional to take over a halfway-completed job, it is better to take into consideration using one prior to you start. Possibilities are you might need an expert plumber to make tube links.
This post will certainly assist you mount a brand-new tub in your bathroom if you have already purchased a new tub and do not require to transform the plan of your previous water system pipelines.
Your devices as well as material list ought to consist of the following:
Preparing for the Installment
First of all, the supporting structure provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets unit to prevent strain on the bathtub.
Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be quite troublesome because of the limited accessibility that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have actually been removed, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from turning throughout this procedure. When the faucets have been removed, the holes in the bath/basin will certainly have to be cleaned of any old securing compound.
Before proceeding to fit the brand-new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.
Setting up the Tub
Using both wooden boards under its feet, position the tub in the needed setting. The wooden boards are helpful in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bathtub up until the level reviews level.
To install taps, fit all-time low of the furthest adaptable tap adapter to the ideal supply pipe by making a compression sign up with; then do the same for the other tap.
Activate the water supply and check all joints and also new pipework for leaks and tighten them if required. Fill the tub as well as likewise examine the overflow electrical outlet as well as the typical outlet for leaks.
Lastly, fix the bath paneling as described in the producer's instruction manual. Tiling and sealing around the tub must wait until the bath tub has actually been used at the very least once as this will settle it into its final position.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly need a plastic connector to stop damage to the thread. One end of the port fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin ensuring that the washers remain in place in between the faucet and the sink. Safeguard the faucet in place with the manufacturer given backnut. As soon as the faucet is firmly in position, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former type should be linked to the faucet ends initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the fitting can move sufficient to break a rigid seal, causing the water to penetrate the wall in between the bathroom and the tiling, causing problems with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your fixtures and also installations. They are sold in tubes and cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the motion experienced when the bathtub is in usage. The sealer can split relatively early if you do not take into account this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are likewise easily available on the marketplace. It is a good idea to fit the ceramic tiles making use of waterproof or water resistant glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a passionate person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I thought sharing that chunk was essential. Do you know about somebody who is fascinated by the niche? Do not hesitate to promote it. Bless you for your time. Please check our site back soon.
The best? Call us! Report this page